New 725D Draper Platform

Specifications

Compare >>> Select up to 2 models to compare specifications

John Deere725D Draper Platform

Add Model --Please Select-- 730D (Model year 2022) 735D (Model year 2022) 740D (Model year 2022) 94C - 30,36,40,42 94C- 25 2142 2152 3152 Rigid (2018) 3152 Rigid (25-ft) DH- 25 SP25 D50 D60-25ft D125 D65 Rigid (25-ft)

Add Model --Please Select-- 730D (Model year 2022) 735D (Model year 2022) 740D (Model year 2022) 94C - 30,36,40,42 94C- 25 2142 2152 3152 Rigid (2018) 3152 Rigid (25-ft) DH- 25 SP25 D50 D60-25ft D125 D65 Rigid (25-ft)

Cutterbar length	7.8 m 25.5 ft
Knife drive	Base: single (combine use only) Optional: dual knife (combine use only) Base: dual knife (SPW only or SPW/combine combination use)
Knife speed	490 cycles/min
Pickup reel operating speeds	6-54 rpm 137.2-cm (54-in.) reel: 5-44 rpm
Draper belts speed control	Hydraulic from cab

Type	Rigid draper

Type	Straight-line knife drive system
Length	7.8 m 25.5 ft
Knife drive	Base: single (combine use only) Optional: dual knife (combine use only) Base: dual knife (SPW only or SPW/combine combination use)
Knife speed	490 cycles/min
Cutterbar tilt	Base: hydraulic, maximum tilt 9 degree (angle)
Base skid shoe height

General
Number of slats	Six bat poly base Eight bat steel optional (for forage conditions)
Fingers	Base: nylon Optional: steel (typically used in rice or forage conditions)
Diameter	1.067 m 3.5 ft For rice or forage conditions: 1.371 m 4.5 ft
Height control	Hydraulic
Speed control	Hydraulic
Reel lift	Cylinder stroke: 33 cm 13 in. Total range: 39.2 cm 15.4 in.
Reel fore and aft	Cylinder stroke: 35.9 cm 14.1 in. Total range: 62 cm 24.4 in.
Fore of the cutterbar
Reel resume	Base
Reel reverse	Base
Operating speeds	6-54 rpm
Operating speeds (54-in. reel)	5-44 rpm

Number of slats
Diameter
Height control
Speed control
Operating speeds

Width	Rubber coated polyester with V-Guide tracking: 0.7 L 24 oz Side belts: 1.02 m 3.33 ft Center belts: 1.4 m 4.583 ft Center belt not included with SPW configuration
Belt depth
Cleat height	25.4 mm 1 in.
Operating speed	Side belts: variable up to 223 m/min 735 fpm Center belts: 212 m/min 695 fpm Center belt not included with SPW configuration
Speed control	Hydraulic from cab
Center belt reverse	Base: Center belt not included with SPW configuration

Diameter	Two factory-installed options: 356 or 406 mm 14 or 16 in. Feed drum not included with SPW configuration
Feed drum fingers	Steel, heavy-duty, and round with breakaway notch and retainer Diameter: 16 mm 0.625 in.
Number of fingers	18
Auger finger platform	Dual chevron, retracting
Finger reach	152 mm 6 in.
Drum/auger reverse	Base
Operating speed	195 rpm
Center cleanout door	Base

Type	Base: electrohydraulic
Header height sensing on the ground	Base
Header height sensing off the ground

Type	Optional: hydraulic drive
Fingered augers
Size

Platform length	8.5 m 27.9 ft
Overall operating depth	2.4 m 7.9 ft
Transport width, field position	8.1 m 26.5 ft
Transport width on wheel, less dividers
Transport length, hitch extended